diff --git a/resources/profiles/BBL/filament/Bambu PLA Impact @base.json b/resources/profiles/BBL/filament/Bambu PLA Impact @base.json
index 7cdc6f3e4..029a5f66a 100644
--- a/resources/profiles/BBL/filament/Bambu PLA Impact @base.json	
+++ b/resources/profiles/BBL/filament/Bambu PLA Impact @base.json	
@@ -5,13 +5,16 @@
     "from": "system",
     "filament_id": "GFA03",
     "instantiation": "false",
-    "filament_vendor": [
-        "Bambu Lab"
-    ],
     "filament_cost": [
         "25.4"
     ],
     "filament_flow_ratio": [
         "0.95"
+    ],
+    "filament_vendor": [
+        "Bambu Lab"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/Generic PLA High Speed @BBL X1C.json b/resources/profiles/BBL/filament/Generic PLA High Speed @BBL X1C.json
index f2e682804..7263d42f8 100644
--- a/resources/profiles/BBL/filament/Generic PLA High Speed @BBL X1C.json	
+++ b/resources/profiles/BBL/filament/Generic PLA High Speed @BBL X1C.json	
@@ -21,5 +21,8 @@
         "Bambu Lab P1S 0.8 nozzle",
         "Bambu Lab X1E 0.6 nozzle",
         "Bambu Lab X1E 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/Generic PLA Silk.json b/resources/profiles/BBL/filament/Generic PLA Silk.json
index c1011d708..40fa7b252 100644
--- a/resources/profiles/BBL/filament/Generic PLA Silk.json	
+++ b/resources/profiles/BBL/filament/Generic PLA Silk.json	
@@ -24,5 +24,8 @@
         "Bambu Lab X1E 0.4 nozzle",
         "Bambu Lab X1E 0.6 nozzle",
         "Bambu Lab X1E 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1.json b/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1.json
index cedb6ba84..ba16728a5 100644
--- a/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1.json	
+++ b/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1.json	
@@ -12,5 +12,8 @@
         "Bambu Lab X1 0.6 nozzle",
         "Bambu Lab X1 0.8 nozzle",
         "Bambu Lab X1 0.4 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1C.json b/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1C.json
index 7d5a7ecd5..bdfcdeef9 100644
--- a/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1C.json	
+++ b/resources/profiles/BBL/filament/Overture Matte PLA @BBL X1C.json	
@@ -15,5 +15,8 @@
         "Bambu Lab X1E 0.4 nozzle",
         "Bambu Lab X1E 0.6 nozzle",
         "Bambu Lab X1E 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/Overture PLA @BBL X1.json b/resources/profiles/BBL/filament/Overture PLA @BBL X1.json
index c36384a9e..28b917ca5 100644
--- a/resources/profiles/BBL/filament/Overture PLA @BBL X1.json	
+++ b/resources/profiles/BBL/filament/Overture PLA @BBL X1.json	
@@ -12,5 +12,8 @@
         "Bambu Lab X1 0.4 nozzle",
         "Bambu Lab X1 0.8 nozzle",
         "Bambu Lab X1 0.6 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/Overture PLA @BBL X1C.json b/resources/profiles/BBL/filament/Overture PLA @BBL X1C.json
index 15c06a2ca..62a0d4d9e 100644
--- a/resources/profiles/BBL/filament/Overture PLA @BBL X1C.json	
+++ b/resources/profiles/BBL/filament/Overture PLA @BBL X1C.json	
@@ -15,5 +15,8 @@
         "Bambu Lab X1E 0.4 nozzle",
         "Bambu Lab X1E 0.6 nozzle",
         "Bambu Lab X1E 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/P1P/PolyTerra PLA @BBL P1P.json b/resources/profiles/BBL/filament/P1P/PolyTerra PLA @BBL P1P.json
index 7504020d8..5728ac0c5 100644
--- a/resources/profiles/BBL/filament/P1P/PolyTerra PLA @BBL P1P.json	
+++ b/resources/profiles/BBL/filament/P1P/PolyTerra PLA @BBL P1P.json	
@@ -33,5 +33,8 @@
         "Bambu Lab P1P 0.4 nozzle",
         "Bambu Lab P1P 0.6 nozzle",
         "Bambu Lab P1P 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/PolyLite PLA @BBL X1.json b/resources/profiles/BBL/filament/PolyLite PLA @BBL X1.json
index 4ed582192..77a037efd 100644
--- a/resources/profiles/BBL/filament/PolyLite PLA @BBL X1.json	
+++ b/resources/profiles/BBL/filament/PolyLite PLA @BBL X1.json	
@@ -15,5 +15,8 @@
         "Bambu Lab X1 0.4 nozzle",
         "Bambu Lab X1 0.6 nozzle",
         "Bambu Lab X1 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/PolyLite PLA @BBL X1C.json b/resources/profiles/BBL/filament/PolyLite PLA @BBL X1C.json
index c9c27d914..a24021705 100644
--- a/resources/profiles/BBL/filament/PolyLite PLA @BBL X1C.json	
+++ b/resources/profiles/BBL/filament/PolyLite PLA @BBL X1C.json	
@@ -18,5 +18,8 @@
         "Bambu Lab X1E 0.4 nozzle",
         "Bambu Lab X1E 0.6 nozzle",
         "Bambu Lab X1E 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1.json b/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1.json
index d3fd2251c..46e2144b4 100644
--- a/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1.json	
+++ b/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1.json	
@@ -15,5 +15,8 @@
         "Bambu Lab X1 0.4 nozzle",
         "Bambu Lab X1 0.6 nozzle",
         "Bambu Lab X1 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file
diff --git a/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1C.json b/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1C.json
index c3444436a..72378493d 100644
--- a/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1C.json	
+++ b/resources/profiles/BBL/filament/PolyTerra PLA @BBL X1C.json	
@@ -18,5 +18,8 @@
         "Bambu Lab X1E 0.4 nozzle",
         "Bambu Lab X1E 0.6 nozzle",
         "Bambu Lab X1E 0.8 nozzle"
+    ],
+    "filament_start_gcode": [
+        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
     ]
 }
\ No newline at end of file