1.Always set filament retract params to filament_num size.In
gcode export module, we can always use filament idx to get
retract params
2. add logic in update_filament_maps_to_config to update the
retraction related params which can be overiden by filament
jira:NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: Ia45dd1401aa3565d062d5da1c9f4a2ba8966f693
The length of default value for extruder printable height
should be same with extruder printable area
jira:NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: I01bf5e2a9ddb2faadbbe0a01f4ff2c5582b8ac45
1. Pre cooling extruder after the extruder used
2. Pre heating before the extruder used
3. Refine the structure of finalize function
jira: NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: I98c92763c006fc9564db45a4a5d542b891ea1aa2
1. add slicing errors for gcode in unprintable area, also for filament mapping
2. use common area for auto arrange
3. support filament_map/filament_map_mode related params
4. add logic to check the filament maps before slicing
5. uptodate support multi-extruder
6. switch new machine/filament support multi-extruder
7. process config params support transfer between mult-extruder and
single-extruder
8. improve machine-limit logic support multi-extruder
9. flush-volume support multi-extruder
10. add default params to support auto mapping slicing
jira: no-jira
Change-Id: Ice39a365841322ddb586d39c56ff923626822528
* Init port of Cura's MM interlocking
* Refactor a bit
* Fix crash when bottom surface is multi-color
* Fix crash when boundary avoidance is 0
* Add config
---------
Co-authored-by: zhimin.zeng <zhimin.zeng@bambulab.com>
jira: none
Change-Id: I81cacddf46ad5921a7a2a23fff07cc17addceb6f
1. Machine with multi extruder should set length of extruder offset
to extruder num
2. Register retract_restart_extra
jira:NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: Ic3eb324cb91dc70b091c8922936d2709c361cc38
1.Use max flow network to handle limit
2.Support setting master extruder id
3.Fix the issue in the KMedoids algorithm where data is overwritten
after each retry.
jira:NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: Idd2bedf39f61e7a65eb4199852f60b8fbebe0a7d
1. Nozzle Volume and Nozzle Type support multi extruder now
jira:NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: Ie171b5105bd3830db3a992cadd365b785008c47a
1. also remove original nozzle_volume_type from printer
and move into project config
2. support save nozzle_volume_type into appconfig
and load from it at beginning or printer switch
jira: no-jira
Change-Id: I01fc82d142fc633fc59a238796a71b9f8d180efb
1.Save multi extruder state in gcode processor
2.Add machine exturder change time
3.Fix some naming issues
jira:NONE
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: I9785331290515eeb908ff0ff01aad5aac44212d9
1.During the filament change, the extruder will extrude an extra length
of grap_length for the corresponding detection, so the purge volume can
reduce this length.
jira:NEW
Signed-off-by: xun.zhang <xun.zhang@bambulab.com>
Change-Id: I14f55a3200c1dd48b1603e50280d0c29e1319ebe
xun.zhang
lane.wei
zhimin.zeng
Noisyfox
qing.zhang